Agilex™ 7 FPGA I-Series Development Kit User Guide

Download PDF
ID 683288
Date 4/05/2024
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Board Setup 4. Board Test System 5. Document Revision History for the Agilex™ 7 FPGA I-Series Development Kit User Guide A. Development Kits Components B. Additional Information
1. Overview x
1.1. Block Diagram 1.2. Box Contents 1.3. Operating Conditions
2. Getting Started x
2.1. About Quartus® Prime Software 2.2. Development Board Package 2.3. Installing the Intel® FPGA Download Cable II Driver
2.1. About Quartus® Prime Software x
2.1.1. Activating Your License
3. Development Board Setup x
3.1. Applying Power to the Development Board 3.2. Default Switch Settings 3.3. How to Generate a POF Image to Program the Flash 3.4. How to Program the Generated POF Image 3.5. The Required SmartVID QSF Assignments to Compile a Design
3.2. Default Switch Settings x
3.2.1. Default Settings 3.2.2. Perform Board Restore through Quartus® Prime Programmer
4. Board Test System x
4.1. Set Up BTS GUI Running Environment 4.2. Test the Functionality of the Development Kit 4.3. Control On-board Clock through Clock Controller GUI 4.4. Monitor On-board Power through Power Monitor GUI 4.5. BTS Test Areas 4.6. Identify Test Pass or Fail-based on BTS GUI Test Status
4.1. Set Up BTS GUI Running Environment x
4.1.1. Download OpenJDK 4.1.2. Download OpenJFX 4.1.3. Install OpenJDK and OpenJFX 4.1.4. Run BTS GUI
4.2. Test the Functionality of the Development Kit x
4.2.1. The Bottom Info Bar 4.2.2. The Configure Menu 4.2.3. The Sys Info Tab 4.2.4. The GPIO Tab 4.2.5. The XCVR Tab 4.2.6. The RAM Tab
4.2.5. The XCVR Tab x
4.2.5.1. The QSFPDD NRZ Tab 4.2.5.2. The QSFPDD PAM4 Tab
A. Development Kits Components x
A.1. Board Overview A.2. Agilex™ 7 FPGA I-Series A.3. PCIe* and CXL Interfaces A.4. MCIO Connector A.5. MCIO Cable Assembly Information A.6. Network Interfaces A.7. Port Controller A.8. FPGA Configuration A.9. Supported Configuration Modes A.10. Memory Interfaces A.11. I2C A.12. Clock Circuits A.13. System Power A.14. Temperature Monitoring A.15. Mechanical Requirements A.16. Board Thermal Requirements A.17. Board Operating Conditions A.18. Over Temperature Warning LED
A.13. System Power x
A.13.1. Power Guidelines A.13.2. Power Distribution System A.13.3. Power Sequence A.13.4. Power Measurement
B. Additional Information x
B.1. Safety and Regulatory Information B.2. Compliance Information
B.1. Safety and Regulatory Information x
B.1.1. Safety Warnings B.1.2. Safety Cautions
1. Overview
2. Getting Started
3. Development Board Setup
4. Board Test System
5. Document Revision History for the Agilex™ 7 FPGA I-Series Development Kit User Guide
A. Development Kits Components
B. Additional Information

A.14. Temperature Monitoring

Temperature monitoring of the Agilex™ 7 FPGA device is done by a pair of MAX31730ATC+ temperature sense devices. The Agilex™ 7 FPGA device has 6 die temperature diodes that can be monitored via external temperature sensing devices. The MAX31730ATC+ senses these diodes and convert the signals to digital form for the MAX® 10 to read via a I2C bus. Additionally, the THERMn signal from the MAX31730ATC+ are brought to the MAX® 10 to allow it to immediately sense a temperature fault condition. An over temperature warning LED D9 (Red-colored) is controlled by the MAX® 10 device to indicate an over temperature warning. Temperature fault set points can be programmed into the temperature sensing device.

Figure 48. Board Temperature Measurement Circuit
Level Two Title