Intel® Stratix® 10 SX SoC Development Kit User Guide

Download PDF
ID 683303
Date 6/02/2023
Public
Document Table of Contents
Document Table of Contents x
1. Overview 2. Getting Started 3. Development Kit Setup 4. Development Kit Components 5. Board Test System A. Additional Information B. Revision History
1. Overview x
1.1. General Development Kit Description 1.2. Recommended Operating Conditions 1.3. Handling the Development Kit
2. Getting Started x
2.1. Installing Quartus Prime Software 2.2. Installing the Intel® FPGA Download Cable 2.3. Installing the Intel SoC Embedded Development Suite (EDS) 2.4. Installing the Intel® Stratix® 10 SX SoC Development Kit Package
3. Development Kit Setup x
3.1. Inspect the Development Kit 3.2. Default Setup of the Development Kit 3.3. Intel® MAX® 10 System Controller Updates
4. Development Kit Components x
4.1. Development Kit Feature Summary 4.2. Board Components 4.3. Intel® Stratix® 10 SoC Device Overview 4.4. Intel® MAX® 10 System Controller Overview 4.5. FPGA Configuration 4.6. General User Input/Output 4.7. Connectors and Interfaces 4.8. Daughter Cards 4.9. System Memory 4.10. System Power
4.7. Connectors and Interfaces x
4.7.1. PCIe* Slot 4.7.2. ZQSFP+ 4.7.3. SFP+ 4.7.4. HDMI 4.7.5. SDI Port 4.7.6. MXP 4.7.7. Intel® FPGA Download Cable Direct Port (Debug Port) 4.7.8. FMC+ A/B Slot 4.7.9. FMC+ A/B LVDS Interfaces (LPC Pins) 4.7.10. LMK05028 Jitter Attenuator 4.7.11. FPGA-IOMAX10 Interface
4.8. Daughter Cards x
4.8.1. HPS IO-48 OOBE Daughter Card 4.8.2. HPS IO-48 NAND Flash Daughter Card 4.8.3. HPS Boot Flash Card
4.8.3. HPS Boot Flash Card x
4.8.3.1. Boot QSPI Flash Daughter Card 4.8.3.2. Boot MicroSD Daughter Card 4.8.3.3. Boot eMMC Daughter Card
4.9. System Memory x
4.9.1. FPGA Memory (DDR4 SO-DIMM) 4.9.2. HPS Memory (External 4 GB HILO x72 DDR4 ) 4.9.3. HPS I2C Interface
4.10. System Power x
4.10.1. Power Supply Options 4.10.2. Power Sequence 4.10.3. Power Distribution Network
5. Board Test System x
5.1. Preparing the Board 5.2. Running the BTS 5.3. Using the BTS
5.3. Using the BTS x
5.3.1. The Configure Menu 5.3.2. The GPIO Tab 5.3.3. The QSFP/SFP Tab 5.3.4. The PCIE Tab 5.3.5. The MXP Tab 5.3.6. The FMCA Tab 5.3.7. The FMCB Tab 5.3.8. The DDR4 Tab 5.3.9. Power Monitor 5.3.10. The Clock Control
A. Additional Information x
A.1. Modify the Intel® Stratix® 10 SX SoC Development Kit to use a battery for the BBRAM A.2. Modify the Intel® Stratix® 10 SX SoC Development Kit HPS DDR4 memory width and ECC configuration using the Golden Hardware Reference Design project A.3. Safety and Regulatory Information A.4. Compliance Information
A.3. Safety and Regulatory Information x
A.3.1. Safety Warnings A.3.2. Safety Cautions
A.4. Compliance Information x
A.4.1. Compliance and Conformity Statements
B. Revision History x
B.1. Revision History
1. Overview
2. Getting Started
3. Development Kit Setup
4. Development Kit Components
5. Board Test System
A. Additional Information
B. Revision History

5.1. Preparing the Board

After successful FPGA configuration, with the power to the board off, follow these steps:
  • Connect the USB cable to your PC and the Intel® FPGA Download Cable II port.
  • Change SW1 and SW4 to the following configuration.
  • Turn on power to the board and run the Board Test System.
Note: To ensure operating stability, keep the USB cable connected and the board powered on when running the demonstration application.
Table 49.  SW1 GUI Mode
Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8
OFF OFF ON ON ON ON ON ON
Table 50.  SW4 GUI Mode
Bit 1 Bit 2 Bit 3 Bit 4
ON OFF ON ON
Level Two Title