Cyclone V Device Datasheet

Download PDF
ID 683801
Date 5/23/2023
Public
Document Table of Contents
Document Table of Contents x
Cyclone V Device Datasheet
Cyclone V Device Datasheet x
Electrical Characteristics Switching Characteristics Configuration Specifications I/O Timing Glossary Document Revision History for Cyclone® V Device Datasheet
Electrical Characteristics x
Operating Conditions
Operating Conditions x
Absolute Maximum Ratings Maximum Allowed Overshoot and Undershoot Voltage Recommended Operating Conditions DC Characteristics I/O Standard Specifications
Recommended Operating Conditions x
Recommended Operating Conditions Transceiver Power Supply Operating Conditions HPS Power Supply Operating Conditions
DC Characteristics x
Supply Current and Power Consumption I/O Pin Leakage Current Bus Hold Specifications OCT Calibration Accuracy Specifications OCT Without Calibration Resistance Tolerance Specifications OCT Variation after Power-Up Calibration Pin Capacitance Hot Socketing Internal Weak Pull-Up Resistor
I/O Standard Specifications x
Single-Ended I/O Standards Single-Ended SSTL, HSTL, and HSUL I/O Reference Voltage Specifications Single-Ended SSTL, HSTL, and HSUL I/O Standards Signal Specifications Differential SSTL I/O Standards Differential HSTL and HSUL I/O Standards Differential I/O Standard Specifications
Switching Characteristics x
Transceiver Performance Specifications Core Performance Specifications Periphery Performance HPS Specifications
Transceiver Performance Specifications x
Transceiver Specifications for Cyclone V GX, GT, SX, and ST Devices CTLE Response at Data Rates > 3.25 Gbps across Supported AC Gain and DC Gain CTLE Response at Data Rates ≤ 3.25 Gbps across Supported AC Gain and DC Gain Typical TX VOD Setting for Cyclone® V Transceiver Channels with termination of 100 Ω Transmitter Pre-Emphasis Levels Transceiver Compliance Specification
Core Performance Specifications x
Clock Tree Specifications PLL Specifications DSP Block Performance Specifications Memory Block Performance Specifications
Periphery Performance x
High-Speed I/O Specifications DLL Frequency Range Specifications DQS Logic Block Specifications Memory Output Clock Jitter Specifications OCT Calibration Block Specifications Duty Cycle Distortion (DCD) Specifications
HPS Specifications x
HPS Clock Performance HPS PLL Specifications Quad SPI Flash Timing Characteristics SPI Timing Characteristics SD/MMC Timing Characteristics USB Timing Characteristics Ethernet Media Access Controller (EMAC) Timing Characteristics I2C Timing Characteristics NAND Timing Characteristics Arm* Trace Timing Characteristics UART Interface GPIO Interface CAN Interface HPS JTAG Timing Specifications
HPS PLL Specifications x
HPS PLL VCO Frequency Range HPS PLL Input Clock Range HPS PLL Input Jitter
Configuration Specifications x
POR Specifications FPGA JTAG Configuration Timing FPP Configuration Timing Active Serial (AS) Configuration Timing DCLK Frequency Specification in the AS Configuration Scheme Passive Serial (PS) Configuration Timing Initialization Configuration Files Minimum Configuration Time Estimation Remote System Upgrades User Watchdog Internal Oscillator Frequency Specifications
FPP Configuration Timing x
DCLK-to-DATA[] Ratio (r) for FPP Configuration FPP Configuration Timing when DCLK-to-DATA[] = 1 FPP Configuration Timing when DCLK-to-DATA[] >1
I/O Timing x
Programmable IOE Delay Programmable Output Buffer Delay
Cyclone V Device Datasheet

Initialization

Table 64.  Initialization Clock Source Option and the Maximum Frequency for Cyclone® V Devices
Initialization Clock Source Configuration Scheme Maximum Frequency (MHz) Minimum Number of Clock Cycles
Internal Oscillator AS, PS, and FPP 12.5 Tinit
CLKUSR 95 PS and FPP 125
AS 100
DCLK PS and FPP 125
95 To enable CLKUSR as the initialization clock source, turn on the Enable user-supplied start-up clock (CLKUSR) option in the Intel® Quartus® Prime software from the General panel of the Device and Pin Options dialog box.
Level Two Title